TOP 7 MASTERING MISTAKES AND HOW TO AVOID THEM
Most recording musicians, engineers and producers are well aware of what a difference mastering can make to our mixes. Mastering is an art form in itself and is best placed in the hands of a specialist.
Email us at firstname.lastname@example.org or call 0208 883 9641
But even expert mastering engineers can only accomplish so much, and it’s largely dependent on the raw materials they’re given to work with.
1. Too Much Bottom
Excessive low-end is probably one of the most common problems in mixes coming from project studios. Usually this is directly related to the mixing environment. The average home studio or project room is lacking in real acoustical treatment is and rife with reflective surfaces and bass traps. The result is an uneven response across the bass spectrum, with some notes being overemphasized and others being practically inaudible. This translates to a poorly balanced low end in your mix. The most egregious mistake is that people’s monitors aren’t placed properly. Speakers need to be as far apart from each other as you are from them. So if your mix position is, say, three feet from either speaker, the speakers should be exactly three feet apart. Moreover, if the speakers are too close or too far from a wall, the apparent bass response will be off.
2. Terrible Treble
On the other end of the spectrum, high-end can also cause its own issues. While not as hard to hear in the project studio environment, those high frequencies can show up differently during the mastering phase. Most mixes will want a bit of ‘polish’ or ‘shine’ in mastering. When this good stuff is applied, sibilance can really creep up. Do yourself a big favour and de-ess your vocals, maybe even your hi-hat just a bit, even if you don’t hear too much of an issue. Your mastering engineer will thank you. The bottom line is to use EQ wisely and sparingly.
3. No Dynamic Range
This is probably one of the most discussed topics in modern music mixing circles. Over the past decade or so, the quest for radio airplay has created a battle for attention that has manifested itself in loudness – the perception being that louder the track, the more it will grab the listener. It’s a mentality that started with TV and radio advertisers (notice how a loud commercial gets your attention) and is a direct result of today’s vastly improved compressor technology, which has enabled us to create “radio mixes” where everything is loud, punchy and in your face. The problem with pumping up the apparent volume on your mix this way is that it works by compressing the dynamic range of your tracks. Dynamic range is defined as the difference between the loudest and softest sounds in your track. Ideally, the tracks you deliver to the mastering house should have peaks of around –3 dB for the loudest material (for example, a snare hit), while the rest of the track should average in the –6 dB to –8 dB area. That would give your peaks somewhere around 3dB to 5dB of dynamic range. The problem with compressing dynamic range (or, equally hazardous, normalizing a track’s relative volume), is that you effectively rob your mastering engineer of the resources to do their job. A good mastering engineer applies meticulous use of multiband compression – bringing up the punch and presence of the bass, adding clarity and sparkle to the high end – all by using different compression algorithms for different spectral bands. Many inexperienced mixers will apply a “mastering compressor” plug-in, using a preset that creates a loud but muddy low-end, a bright and aggressive high-end, and little room for the mastering engineer to add — or de-emphasize — anything.
Sometimes clients desire a ‘loud’ mix, but they have done little or nothing to control the dynamics of their mixes. Layering the limiting (by compressing the vocal, bass, snare, for example) will allow a MUCH more gorgeous detailed, deep shine on the final product! On a related note, try to avoid over-compressing individual tracks for the same reason. Often a mastering engineer will get a track that’s well within dynamic range, but with a vocal track that’s been normalized to the verge of distortion. Again, it leaves little room for mastering to bring out any subtlety or nuance in that vocal.
4. Lack of Panning
It’s important to give your mix some dimensionality by balancing different elements within a nice, wide, stereo field. All too often, people tend to pan everything at or near the center, creating a cluttered-sounding mix that lacks definition. While certain elements should typically be centered (kick, snare, vocal and bass come to mind), panning is a great way to achieve separation between guitar parts, background vocals and other parts of the mix. It’s always good to pan some elements of the mix just a bit off to one side. If you have a blend of guitars, horns, backing vocals, etc., keeping the middle less cluttered allows your ear to hear more distinctly all of that cool production you’ve worked on. You’ll also need less EQ and effects to pick these things out in the mix.
5. Phase Problems
With most DAWs offering unlimited tracks, the temptation to record everything in stereo is strong, and elements like a nicely-recorded stereo acoustic guitar can add depth and character to a track. But be careful to check your mixes in mono to avoid phase cancellation from poorly-placed mics. Only by soloing the stereo tracks will you be able to hear whether certain frequencies “disappear” when the two channels are summed to mono.
It’s not just stereo-miked instruments that can fall victim to phase cancellation. According to Doell, “Often I’ll get a track with ‘hyper-wide’ elements in the mix that achieve that ‘outside the speakers’ effect by making one side out of phase. Just try hitting the mono button and watch that cool keyboard, string pad, background vocal stack, whatever, totally disappear. Even if you never anticipate having any need for mono (AM radio anyone?), when you do this, your balances aren’t what you think!”
This same principle also applies to reverbs. It’s all too common to have that lush hall you placed on the vocal just vanish in mono.
6. Poor Vocal Placement
It’s hard to be objective on placing vocals in a mix, particularly if it’s your song. After all, you know the lyrics, so it’s easy to forget that other people don’t. And in most cases, a track can sound equally “right” whether the vocal is sitting a bit in front or a bit behind the track. Many pros will do two or three alternate mixes of a track, one with the lead vocal a bit up, one with it a bit down, and one in the middle. It’s a luxury of choice that most mastering engineers are happy to have.
7. Misaligned Tracks
This one is a no-brainer. When you send stems (separated groups of tracks, like drums and bass, guitars, backing vocals) to mastering, make sure they all start at the same place. If the lead vocal doesn’t come in until 0:30, that stem should have 30 seconds of silence at the top!
As you might imagine, there are countless other stumbling blocks that can trip up your mix and make life challenging for your mastering engineer – certainly far more than we can list here. As always, the bottom line is to use your ears, listen carefully, and learn the rules before you break them. If all else fails, keep the potential mistakes above in mind, and you’ll be on your way to better results.
— Daniel Keller & Pete Doell